Arduino controlled Dual Mono AK4490 DAC (Part 2)

Following up on Part 1, it’s time to talk about the “brains of the operation”. Bare with me, this is going to be a rather long read.Hardware selection

The DAC needed to be controlled by a microcontroller so I looked into my options. I wanted something that would:

  • Be easy to program, so the Arduino IDE was a must.
  • Be able to drive a TFT.
  • Have enough storage capacity to store enough code & fonts for the TFT.
  • Be readily available.
  • Be relatively low cost, since it would have no influence on the dac’s SQ.
  • Be easy to build / integrate into a new design, even by a novice.

After some consideration, I decided to use an STM32F103 ready-made module. It would plug in to a “mainboard” of my design, along with the chosen TFT. It would be fast enough, have enough flash & ram, be easy to integrate and develop for and it would cost next to nothing.

Next up was the TFT. I’d seen on Ebay an interesting one that was relatively big, high resolution and inexpensive. It was this one:

It can be found on Ebay by searching for “3.5 tft uno 320 x 480”. Expect to pay 6-8€ inc. shipping.

After some searching I found a suitable library that (after some slight tinkering) would allow my tiny STM32 to drive it properly. (Note: do not download the library from this link. I will provide a customized version of the library together with my code).

I found a ready-made library for configuring the Si570 and modified it to run on my STM32, using one of its hardware I2C ports. I will also include this library in my code. To complete the recipe I also found working rotary encoder and IR receiver libraries.

The code

Next up was the prototyping work. I adapted my TFT HiFiDuino Pro code to run on the STM32 & TFT combo, with support for AK4490 dual mono operation. The end result had this feature list:

  • Support for either Dual Mono or single chip setups.
  • Support for the Amanero Combo384 USB to I2S module (must be set up as slave with MCLK/2 and F0,1,2,3 enabled).
  • Control with one rotary encoder with push-to-select functionality.
  • IR Remote support.
  • Support for software volume control, from -99dB to 0dB
  • Display incoming signal sampling rate and type, determined by “reading” the relevant I/O pins of the USB to I2S board.
  • Display and control of the AK4490’s digital filter.
  • Selection of the proper MCLK frequency according to incoming SR and type and programming of the Si570 accordingly.
  • Control of “DSD Direct” function of the AK4490s.
  • Control of the DSD Filter’s Frequency (50KHz or 150KHz).
  • Control of the Sound Mode of the AK4490.
  • Choice of either inverted or normal analog output for the AK4490s.
  • Choice of two sets of MCLK frequencies, either 22/24MHz or 45/49MHz.
  • Remote power on/off functionality (or always on – configurable in the code).

Software Requirements:

In the download I am including the modified versions of the libraries (as mentioned above) as well as the necessary font files. Be sure to extract the contents of “Libraries (place in Libraries folder)” to your Arduino IDE’s “libraries” folder.

Download it here: aKduino v2 (140 downloads)

Here is the revision history:

v1.72 24/12/2017:

  • Minor changes to make compatible with current stm32duino core (changed HardWire.h to Wire.h and other minor stuff).
  • First public release as part of completed dual mono DAC project.

v1.66 10/10/2017:

  • Minor volume bugfix.
  • SuperSlow filter still problematic.
  • Enabled DAC synchronization feature (experimental..).

v1.64 30/09/2017:

  • Bugfixes.

v1.60 20/09/2017:

  • Added support of rotary encoder and IR remote control.
  • 3.5″ TFT support.

v1.50 07/01/2017:

  • Added support of rotary encoder for volume control.
  • Bugfixes related to DSD.

v1.41 06/01/2017:

  • Added support for dual mono mode.

v1.36 03/01/2017:

  • Added very basic TFT support.

v1.35 20/12/2016:

  • Code cleanup for first public release.

v1.33 19/12/2016:

  • Added full control of sound parameters through serial port.

v1.27 18/12/2016:

  • First functional version.
  • Automatic switching between PCM and DSD by monitoring DSDPIN.

The “motherboard”

After I was certain that everything related to the software was working the way it should, I designed a “motherboard” that would take care of the following:

  • Accept the STM32F106 board.
  • Accept the 3.5″ TFT.
  • Accommodate an 24LC256 EEPROM chip, used to store the DAC’s configurable settings.
  • Accommodate two sets of I2C signal isolators and I/O expanders.
  • Include headers for the encoder, IR receiver, power relay, non-isolated and isolated I2C communication, unused uC pins, etc.

This is what I ended up with:

Basic Hardware Requirements:

  • STM32F106 module (a.k.a. “blue pill”, search Ebay for “stm32f106c8t6 board”)
  • 3.5″ TFT with resolution of 320 x 480 (Search Ebay for “3.5 tft uno 320 x 480”)
  • 24LC256 EEPROM chip
  • I2C Isolator ICs, I/O expanders, passive components, etc (see BoM)
  • Rotary Encoder
  • IR Receiver
  • Compatible IR remote control (Apple Remote or other – in any case you must edit the code and input the proper IR codes for your remote, see below)
STM32 TFT Motherboard Bill of Materials
PCB Part Value Notes
C1, C2, C3, C4, C5, C6, C7, C10, C11 100n, 0805
D1 1N4001, DO214BA
L2 Ferrite bead, low R, 1206/3216
LED1, LED2 LED 1206
Q1 AO3400, SOT23
Q2 BC808, SOT23
R1, R2, R3, R4, R12, R13 2.2 – 3.3Κ, 0805
R5, R7 2.2K, 0805
R6 5.1K, 0805
R8, R11 1K, 0805
R9, R10 10K, 0805
U1 24LC256, SO-08
U2, U4 SI8605, SOIC-16
U3, U5 MCP23008, SO-18W
DC_5V .100 (2.54mm) – 2 Pin
EXP .100 (2.54mm) – 2×4 Pin
I2C .100 (2.54mm) – 3 Pin
I2C_ISOL1A, I2C_ISOL1B .100 (2.54mm) – 6 Pin
I2C_ISOL2 .100 (2.54mm) – 3 Pin
IR .100 (2.54mm) – 3 Pin
JP1, JP2 .100 (2.54mm) female – 6 Pin
JP3, JP4 .100 (2.54mm) female – 8 Pin
UART .100 (2.54mm) – 3 Pin
MCP_ISOL1 .100 (2.54mm) – 10 Pin
MCP_ISOL2 .100 (2.54mm) – 2×6 Pin
POWER_RELAY .100 (2.54mm) – 2 Pin
ROTENC .100 (2.54mm) – 4 Pin
STM32_BLUE_PILL STM32F103C uC board

How do I make it work?


You have to supply the board with 5VDC at ~300mA through header DC_5V.

Pin Function
+ 5VDC

Basic connectivity

Serial port:

Pin No. Function
1 RXD (PA10)
2 TXD (PA9)

Rotary encoder:

Pin No. Function
1 PB13
2 PB14
3 PB15

IR control:

Pin No. Function
1 PB9
3 Vcc

If you will be controlling a power on/off relay, you can use the POWER_RELAY header:

Pin Function
+ 5VDC

Expansion header:

Pin No. Function
1 3.3V
3 PB3
4 PA8
5 PA15
6 PB1
7 PA12
8 PB0

I2C header (non-isolated):

Pin No. Function
2 SCL (PB10)
3 SDA (PB11)

Isolated I2C ports

The board has provisions for two separately isolated I2C ports, complete with I/O expanders on their isolated sides. The idea is to connect the DAC board to one of the isolated ports (I2C_ISOL1 & MCP_ISOL1) and your USB-to-I2S board to the other isolated port (usually MCP_ISOL2)

Pin No. Function
1 3.3V (isolated)
2 SDA (PB11)
3 OUT (PC13)
4 IN (PC14)
5 SCL (PB10)
6 GND (isolated)

Pin No. Function
1 3.3V (isolated)
2 GP0
3 GP1
4 GP2
5 GP3
6 GP4
7 GP5
8 GP6
9 GP7
10 GND (isolated)
Pin No. Function
1 SCL (PB10)
2 SDA (PB11)
3 GND (isolated)
Pin No. Function
1 3.3V (isolated)
2 PC15
3 PA11
4 GP0
5 GP1
6 GP2
7 GP3
8 GP4
9 GP5
10 GP6
11 GP7
12 GND (isolated)

That’s it for Part 2. Stay tuned for Part 3: The output stage.

Universal Signal Isolator Shield: Rev. 1.2

Since there has been a lot of interest in my Isolator shield these past few months, I have been optimizing its design.

The result of this optimization is this PCB:
It’s called “the Rev. 1.2”.

Nothing major has changed. The pinouts are still the same, the major components are the same, the functionality is essentially the same.

The changes are as follows:

  • New SPI header. It just passes through the SPI signals, nothing more. It does not connect to anything on the board.
  • New SPI_CS header. Useful only if / when connecting SPI peripherals.
  • Reset button. Because you never know..
  • New circuitry for the POWER_RELAY header. It now uses a MOSFET and it includes a diode for the reverse current coming back from the relay’s coil.
  • Decoupling cap for the IR receiver. Not absolutely necessary, but good to have.
  • More decoupling for the DC_UNR input.
  • Ground planes. Lower Arduino noise, at least in theory.

Here is the updated parts placement:

And this is the updated BoM:

USI Bill of Materials, Rev. 1.2
PCB Part Value Notes
U1 24LC256 SO-08 EEPROM chip
U2 Si8605 SOIC-16 I2C Isolator
U3 MCP23008 SO-18W 8 input/output port expander
U4 Si8642 QSOP-16 Serial port isolator
U5 ADUM1250 SOIC-8 I2C Isolator
Q1 BC856, BC808 or other equivalent PNP SOT-23 TFT backlight control
Q2 BC856, BC808 or other equivalent PNP SOT-23 port expander transistor
Q3 BC856, BC808 or other equivalent PNP SOT-23 port expander transistor
Q4 BC856, BC808 or other equivalent PNP SOT-23 port expander transistor
Q5 AO3400 or other equivalent N-Channel MOSFET SOT-23 power relay mosfet
B1 Bridge rectifier 1A DB107 DIP-4
C1 1000uF 16V
C2 100n 1206
C3 100n 1206
C4 100n 1206
C5 100n 1206
C6 100n 1206
C7 100n 1206
C8 100n 0805
C9 100n 0805
C10 100n 1206
C11 100n 1206
R1 8.2K 1206
R2 2K 1206 pull-up resistor (optional)
R3 2K 1206 pull-up resistor (optional)
R4 5.1K 1206
R5 5.1K 1206
R6 5.1K 1206
R7 2K 0805 pull-up resistor (optional)
R8 2K 0805 pull-up resistor (optional)
R9 8.2K 1206
R10 10K 1206
D1 1N9001 DO214BA
L1 Ferrite Bead, low DC resistance, 3216
L2 Ferrite Bead, low DC resistance, 3216
Reset PCB-mount momentary switch

Soon I will update the shield’s page with the new info.